- DSP log - http://www.dsplog.com -

Modeling phase noise (frequency domain approach)

Posted By Krishna Sankar On September 30, 2012 @ 4:57 pm In Analog,DSP | 1 Comment

In typical wireless system simulations, there is  a need to model the phase noise profile of the local oscillator. For eg, the phase noise profile of the oscillator can be of the shape described in the post on Phase Noise Power Spectral Density to Jitter [1]. While looking around for example Matlab code, found two references [1, 2] which uses the approach of defining the phase noise profile in frequency domain, and then using ifft() to convert to the time domain samples. This post gives a brief overview of the modeling and provides an example Matlab/Octave code.

Modeling

a) Assume a system with sampling frequency $f_s$ Hz and having $N$  samples. In frequency domain we can define $\[-\frac{f_s}{2}, \frac{f_s}{2}\)$ in steps of $\Delta f=\frac{f_s}{N}$ Hz.

b) Consider a phase noise profile defined as follows :

 freq PSD, dBc/Hz 0 -65 1kHz -65 10kHz -95 100kHz -115 1MHz -125 10MHz -125

Table : Example phase noise profile

From the phase noise profile, using linear interpolation (in log10 of the frequency axis), to find the phase noise power spectral density for frequencies from $\[-\frac{f_s}{2}, \frac{f_s}{2}\)$ in steps of $\Delta f=\frac{f_s}{N}$ Hz.

c) Generate a white Gaussian noise sample of length $N$ and scale it with the phase noise power spectral density

(Scaling by $\sqrt{\Delta f}$ is to normalize the resolution bandwidth to unity)

d) Use ifft() to find the time domain samples.

e) On the rel samples obtained from step (d), take $\e$${jx}$$$ to form the time domain phase noise samples.

Note :

When x is small, $\e$${jx}$$\approx 1 + jx$.

Example Matlab script

% Script for simulating the an example phase noise profile
% ----------------------------------------------------------

clear all; close all;
fs_Hz    = 20e6;
N        = 10^5;
nIter    = 100;

% phase noise profile
psd_f_hz           = [  0  1e3  1e4  1e5  1e6  10e6];
psd_val_dbc_per_hz = [-65  -65  -95 -115 -125  -125];

% defining the frequency vector
freq_v_Hz = [0:N/2]/N*fs_Hz;
delta_f   = fs_Hz/N;
slope    = [psd_val_dbc_per_hz(2:end) - psd_val_dbc_per_hz(1:end-1) ]./...
(log10(psd_f_hz(2:end)) - log10(psd_f_hz(1:end-1)));
constant = 10.^(psd_val_dbc_per_hz(1:end-1)/10).* ...
(psd_f_hz(1:end-1).^(-slope/10));
integral = constant.*(psd_f_hz(2:end).^(1+slope/10) - ...
psd_f_hz(1:end-1).^(1+slope/10) )./(1+slope/10);
%% finding the rms jitter
% finding index with slope == -10
idx = find(slope==-10);
integral(idx) = constant(idx).*(log(psd_f_hz(idx+1)) - log(psd_f_hz(idx)));

% interpolating the phase noise psd values
psd_ssb_dB = -Inf*ones(1,N/2+1); % from [0:N/2]
for ii=1:length(psd_f_hz)-1
[tt1 fl_idx ] = (min(abs(psd_f_hz(ii) - freq_v_Hz)));
[tt2 fr_idx ] = (min(abs(psd_f_hz(ii+1) - freq_v_Hz)));
fvec = [freq_v_Hz(fl_idx):delta_f:freq_v_Hz(fr_idx)];
pvec = slope(ii)*log10(fvec+eps) + psd_val_dbc_per_hz(ii) - slope(ii)*log10(psd_f_hz(ii)+eps);
psd_ssb_dB(fl_idx:fr_idx) = pvec;
end

% forming the full vector from [-N/2:-1 0:N/2-1 ]/N*fs_Hz
psd_dB                  = -Inf*ones(1,N);
psd_dB([-N/2:-1]+N/2+1) = psd_ssb_dB([N/2+1:-1:2]);
psd_dB([0:N/2-1]+N/2+1) = psd_ssb_dB(1:N/2);

psd_linear = 10.^(psd_dB/20);

for (jj = 1:nIter)
% defining frequency vector
phase_noise_freq       = 1/sqrt(2)*(randn(1,N) + j*randn(1,N));
phase_noise_freq_scale = N*sqrt(delta_f)*phase_noise_freq;
phase_noise_freq_psd   = phase_noise_freq_scale .*psd_linear;

% converting to time domain
phase_noise_td      = ifft(fftshift(phase_noise_freq_psd));
pn_td               = exp(j*(sqrt(2)*real(phase_noise_td)));

% for estimating jitter and plotting
pn_without_carrier  = (pn_td - 1);

hF           = 1/(N*sqrt(delta_f))*fft(pn_without_carrier,N);
hFPwr(jj,:)  = hF.*conj(hF);
end

figure
semilogx( [-N/2:N/2-1]/N*fs_Hz, 10*log10(fftshift(mean(hFPwr))), 'r^-' );
hold on;grid on;
semilogx([0:N/2]/N*fs_Hz,psd_ssb_dB,'mp-');
semilogx(psd_f_hz,psd_val_dbc_per_hz,'bs-');
legend('est-freq-response','original','interpolated');
xlabel('freq, Hz'); ylabel('dBc/Hz');
axis([1 10e6 -140 -50]); title(title_str);

[2]

Figure : Example phase noise profile (expected and simulated)

Summary

The above approach seems to allow a way to model an arbitrary phase noise power spectral density. However, the fact that this approach needs a large ifft() of length $N$can potentially slow down the simulation.

References

[1] Phase Noise by Alex Bar-Guy [3], 27 Oct 2005 (Updated 08 Dec 2005) http://www.mathworks.com/matlabcentral/fileexchange/8844-phase-noise [4]

[2]  Baseband-equivalent phase noise model, Submitted by Markus Nentwig [5] on Dec 18 2011

URL to article: http://www.dsplog.com/2012/09/30/modeling-phase-noise-frequency-domain/

URLs in this post:

[1] Phase Noise Power Spectral Density to Jitter: http://www.dsplog.com/2012/06/22/phase-noise-psd-to-jitter/